BENINCA BILL40M Swing Gate Motor – Up to 3.5M Per Leaf

BENINCA BILL40M 230V Commercial Swing Gate Motor UAE

BENINCA BILL40M is a professional 230V electromechanical linear swing gate actuator designed for automatic gates with leaves up to 3.5 metres each. BENINCA classifies the BILL40M for commercial use, making it suitable for villas, residential compounds, commercial properties and other medium-to-large swing gate entrances.

The BILL40M provides up to 2800 N maximum thrust with a 400 mm standard stroke, 18-second opening time and IP54 protection. Its compact design, stainless-steel stem and protected worm screw make it particularly suitable for outdoor installations exposed to dust, sand and demanding atmospheric conditions.

BENINCA BILL40M Key Features

• Genuine BENINCA swing gate actuator
• Model: BILL40M
• For swing gates up to 3.5 m per leaf
• Commercial-use gate automation
• 230V AC electromechanical geared motor
• Irreversible operator design
• 2800 N maximum thrust
• 18-second opening time
• 400 mm standard stroke
• 420 mm maximum stroke
• 30% duty cycle
• IP54 protection rating
• Stainless-steel stem
• Worm screw protected by scraper ring
• Suitable for dusty and sandy environments
• Compact installation geometry
• Easy manual release access from above
• Available in right-hand and left-hand versions
• Grease lubrication
• Operating temperature from -20°C to +50°C

BENINCA BILL40M Technical Specifications

For Swing Gates Up to 3.5 Metres Per Leaf

The BENINCA BILL40M is designed for swing gate leaves measuring up to 3.5 metres. For a standard double swing gate, one BILL40M actuator is normally installed on each gate leaf.

Correct motor selection should also consider gate weight, hinge geometry, wind exposure, gate construction and daily operating frequency rather than leaf length alone.

2800 N Maximum Thrust

The BILL40M provides up to 2800 N maximum thrust, delivering strong and controlled movement for correctly installed medium-to-large swing gates.

The combination of 2800 N thrust and a 400 mm standard stroke makes the BILL40M suitable for installations requiring a longer actuator stroke than the smaller BILL30M.

400 mm Stroke & 18-Second Opening

The BENINCA BILL40M features a 400 mm standard stroke with a maximum available stroke of 420 mm. Its specified opening time is approximately 18 seconds.

Actual gate opening time can vary according to installation geometry and the required opening angle.

Designed for Dusty & Sandy Environments

The BILL40M uses a stainless-steel actuator stem and a worm screw protected by a scraper ring. This construction helps protect the actuator mechanism in installations exposed to dust, sand and aggressive atmospheric conditions.

These characteristics make the BILL40M particularly suitable for professional outdoor swing gate installations in UAE conditions.

Compact Design for Wrought-Iron Gates

BENINCA designed the BILL series with a compact and neat profile, making the BILL40M particularly suitable for wrought-iron and decorative swing gates where the appearance of the automation system is important.

Manual Release System

The BILL40M provides convenient access to its manual release mechanism from above. The gate can therefore be released for manual movement when required during a power failure or maintenance procedure.

External BENINCA Control Unit

The BILL40M does not contain an integrated control board. One or two actuators are operated using a compatible external BENINCA 230V swing gate control unit.

The official KBILL40M kit currently uses the BENINCA HEADY control unit, which includes an integrated 433.92 MHz radio receiver and supports automatic and semi-automatic operating logic, pedestrian opening, photocells, flashing light and other gate automation functions.

Virtual Encoder Management

The BILL40M does not contain a conventional integrated physical encoder. With compatible BENINCA control electronics, an encoder signal can be recreated from measurements of the electric motor's operating parameters.

This allows compatible control systems to improve slowdown management, monitor gate travel and calculate torque in relation to gate position.

BENINCA BILL30M vs BILL40M

Official BENINCA KBILL40M Kit

• 2 × BENINCA BILL40M 230V Swing Gate Motors
• 1 × BENINCA HEADY 230V Control Unit
• 1 × Pair BENINCA PUPILLA.T Adjustable Photocells
• 1 × BENINCA STAR Flashing Light with Built-In Antenna
• 1 × BENINCA TO.GO2VA 2-Channel 433.92 MHz Remote Control

Note: The official factory kit and our UAE package may contain different accessories. Confirm the exact package contents when ordering.

BENINCA BILL40M Applications

• Commercial swing gates
• Villa entrance gates
• Residential compounds
• Wrought-iron gates
• Decorative steel gates
• Double-leaf swing gates
• Single-leaf swing gates
• Commercial property entrances
• Private driveway gates

BENINCA BILL40M Supply & Installation UAE

We supply BENINCA BILL40M swing gate motors throughout the UAE with professional installation, replacement and technical support available according to site requirements.

Supply and installation are available across Dubai, Sharjah, Abu Dhabi, Ajman, Ras Al Khaimah, Fujairah, Umm Al Quwain and Al Ain.

For correct motor selection, provide the gate leaf length, approximate gate weight, hinge dimensions, required opening angle and a clear site photo before ordering.